Simrad PI DEPTH Especificações Página 175
- Página / 268
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
References
163
857-164636 / Rev.A
Input
By default, the PI32 is only equipped with one NMEA interface
connector. For this reason, you can only receive data from one
peripheral device. However, this device may provide you with
more than one type of information. For example, GPS systems
will pr ovide you with position, course, speed and navigational
information, and these telegrams are transmitted sequentially on
the same serial line using different telegram types.
If you do not use you Remote connector to interface a
secondary display, you can define this output as an NMEA
interface. For more information, refer to the Interface setup
Remote/Alarm setup page.
Position: Select which telegram you wish to use to receive
position data; either GLL, RMA, RMC or GGA. Then, switch
the interface on or off.
Course: Select which telegram you wish to use to receive
course data; either RMA, RMC or VTG. Then, switch the
interface on or off.
Speed: Select which telegram you wish to use to receive speed
data; either RMA, RMC or VTG. T hen, switch the interface on
or off.
Navigation: The telegrams used to receive navigational data are
fixed, and the PI32 will receive APB, RMB and XTE telegrams.
Switch the interface on or off.
Water temperature: The telegram used to receive water
temperature data is fixed, and the PI32 will receive this
information using the MTW telegram. Switch the interface on
or off.
- Operator manual 1
- Catch monitoring system 3
- About this document 4
- Sections 5
- 12 Sensor test procedures 6
- 13 Technical specifications 6
- Simrad PI32 10
- INTRODUCTION 13
- SYSTEM DESCRIPTION 14
- System diagram 15
- Operator Unit 16
- Sensor overview 18
- Battery chargers 19
- GETTING STARTED 20
- Power on 21
- Power off 21
- Page 1: Echo sounder 22
- Page 2: Numeric display 22
- Page 3: Graphic display 22
- Page 4: Navigation display 22
- Leafing through the pages 23
- Other display presentations 23
- Introduction to the main menu 24
- Introduction to the keypad 25
- Introducing the sensors 27
- Depth: How deep can you go? 29
- Rip: Check for damages! 30
- APPLICATION EXAMPLES 32
- Purse seine 33
- Danish seine 34
- Bottom trawl 35
- Pelagic trawl 36
- Echo sounder 37
- Graphic display 38
- DISPLAY PRESENTATIONS 39
- Numeric display 40
- Depth presentation 43
- Height presentation 44
- Spread presentation 45
- Surface temperature 49
- Status display 50
- → Receiver setup, page 174 51
- Echo sounder display 52
- Bottom expansion 53
- Navigation display 55
- Position display 56
- OPERATIONAL PROCEDURES 57
- → Numeric display, page 28 59
- How to set up the sensors 60
- Predefined settings 61
- How to use the sensors 64
- How to test the sensors 66
- How to define sensor offsets 68
- MENU Exit 72
- GAIN- GAIN+ 72
- (CD11105C) 72
- → Twin Spread, page 128 73
- → Trawl info, page 182 73
- Howtoviewechosounderdata 75
- How to set up marker lines 76
- Depth and Height marker lines 77
- Spread marker line 77
- → Graphic setup, page 160 78
- Access to the parameters 80
- Set up the parameters 80
- Ping to ping filter 82
- Colour threshold 82
- Signal threshold 82
- Depth grid 82
- Standard mode 84
- Phased range mode 84
- Activate A-Scope 88
- De-activate A-Scope 88
- How to define alarm limits 89
- Surface temperature alarm 90
- Clearance alarms 90
- How to select menu language 92
- → Page setup, page 171 93
- PRACTICAL USE OF THE SENSORS 95
- PI Bottom Contact sensor 99
- Bottom Contact presentatio n 100
- Sensor configuration 100
- System configuration 101
- Mounting 101
- 857-164636 / Rev.A 102
- PS Bottom Contact sensor 103
- PI Catch sensor 107
- Presentation 108
- PS Catch sensor 112
- Catch presentation 113
- PI Depth sensor 116
- Numerical presentation 117
- PS Depth sensor 121
- PI Height sensor 126
- Daily operation 127
- PI Rip sensor 130
- Numeric presentation 131
- PI Spread and Remote sensors 135
- Installation principle 138
- Sacrificial water switch 139
- PI Twin Spread 140
- Main parts 141
- PI Temperature sensor 145
- Temperature presentation 147
- PS Temperature sensor 151
- SENSOR CHARGERS 156
- PI Charger 157
- PS30 Charger 159
- General guidelines 160
- Battery depleted frequently 160
- Typical sensor (PI Depth) 160
- MENU SYSTEM 161
- The main menu 162
- Menu system 163
- REFERENCES 164
- Depth calibration 165
- Echo presentation setup 166
- Echo sounder setup 169
- Related topics 170
- Factory presets 171
- Graphic setup 172
- → Sensor setup, page 179 173
- → Numeric setup, page 169 173
- Interface setup NMEA 174
- Applicable telegram formats 177
- Interface setup remote/alarm 179
- Navigation setup 180
- Numeric setup 181
- Offset adjust 182
- Page setup 183
- Palette setup 184
- Position display setup 185
- Receiver setup 186
- Sensor alarms 189
- Sensor setup 191
- Speed setup 192
- Surface temperature setup 193
- Trawl info setup 194
- Units setup 195
- PI CONFIGURATOR 196
- Basic information 197
- Available equipment 198
- About sensor configuration 199
- Changing the update rate 200
- Main dialogue description 201
- Operational procedures 203
- Software installation 204
- How to interface the sensor 205
- References 210
- Communication P o rt Setup 212
- Operation 212
- Configure Sensor 213
- Factory Default 216
- Language 218
- LED Control 219
- Message field 220
- PI Configurator 221
- Ping control 222
- Read Sensor Data 224
- Sensor Type 226
- Show Channel At Startup 228
- Examples 229
- Terminate Communication 230
- Maintenance 231
- Making a programming cable 233
- Troubleshooting 234
- SENSOR TEST PROCEDURES 235
- Bottom Contact test procedure 236
- Testing on land 237
- Testing in water 237
- Catch sensor, test procedure 239
- Depth sensor, test procedure 242
- PI32 Calibration procedure 244
- PI44 Calibration procedure 244
- Height sensor, test procedure 245
- Tools and equipment required 248
- TECHNICAL SPECIFICATIONS 255
- PI Bottom Contact 256
- PI Catch & PI Rip 256
- PI Depth 257
- PI Height 258
- PI Spread & Remote 258
- PI Temperature 259
- - To 70% capacity: 1 hour 260
- - To 100% capacity: 4 hours 260
- - To 100% capacity: 16 hours 260
- E 2005 Simrad AS 268
- ISBN 82-8066-059-3 268
Manuais e produtos relacionados com não Simrad PI DEPTH
não Simrad FS25 Guia do Utilizador
(108 páginas)
(108 páginas)
não Simrad SP60 - REV D Manual do Utilizador
(44 páginas)
(44 páginas)
não Simrad ER60 - REV B Informações Técnicas
(256 páginas)
(256 páginas)
não Simrad ES38-10 - REV B Manual de Instalação
(48 páginas)
(48 páginas)
não Simrad SH90 - REV B Especificações
(2 páginas)
(2 páginas)
não Simrad ES333-7CD - REV A Manual de Instalação
(32 páginas)
(32 páginas)
não Simrad PI HBU - REV A Manual de Instruções
(12 páginas)
(12 páginas)
não Simrad SH80 - REV C Manual de Instalação
(214 páginas)
(214 páginas)
não Simrad ITI Manual do Utilizador
(36 páginas)
(36 páginas)
não Simrad SP60 - REV D Manual de Instalação
(178 páginas)
(178 páginas)
não Simrad EQ 55 Informações Técnicas
(154 páginas)
(154 páginas)
não Simrad SH80 - REV C Manual de Instalação
(200 páginas)
(200 páginas)
não Simrad ROBERTSON AP45 Manual do Utilizador
(8 páginas)
(8 páginas)
não Simrad RS90 Manual do Utilizador
(24 páginas)
(24 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.110 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais